Ground source heat pump installation service

Professional installation service of Ships must be performed by an MCS accredited installer, who should offer warranties and maintenance contracts as part of their package.

 

Your contractor will conduct a manual J load calculation and examine any existing ductwork, to see if installing a ground source heat pump with existing heating distribution infrastructure will reduce costs.

 

Installation

 

Ground source heat pumps harness natural energy found underground to supply heating and hot water to properties. They work by pumping refrigerant through an underground pipe network that absorbs low-grade ambient energy, then pumping it directly to your house where it’s converted to high-grade heat for use by your central heating system, hot water system or underfloor heating system.

 

At the start of installation, your installer will conduct an assessment of your home to assess which ground source heat pump system will best fit with it. They may perform a Manual J calculation which measures your property’s heating and cooling loads before inspecting any existing ductwork to make sure it’s efficient and sealed effectively – this information allows them to create a customized heating/cooling solution just for you!

 

Once the design process is complete, your contractor will excavate horizontal or vertical loop fields and bury pipes beneath the surface. Each site varies; trench locations will depend on how much space there is available as well as which heat pump you install. On average, excavation typically lasts one or two days.

 

Subterranean pipes will be filled with a mixture of water and antifreeze that acts as a heat exchanger, dispensing some liquid to heat your home’s heating systems while returning other fluid to loops to continue cycling.

 

Once the piping has been installed, your contractor will connect it to a heat pump unit and electrical source. Typically located in a plant room, this equipment consists of cylinder, controller and two circulation pumps; be sure that there is plenty of room as this piece requires regular maintenance.

 

Heat pump systems work best when used in combination with low-temperature heating systems such as underfloor or wall-mounted radiators, however if your home lacks sufficient insulation then consider improving this before investing in new heating system – this may help you install smaller heat pumps, saving on both installation and ongoing costs.

 

Commissioning

 

When hiring a contractor to install your ground-source heat pump, it’s essential that you ask about their experience with its installation. Request references and check online reviews; local energy agencies often provide lists of qualified contractors. Make sure your chosen contractor is licensed and insured – additionally they should possess extensive training in designing and installing geothermal heating/cooling systems.

 

Installers begin their evaluation of your property by conducting an in-depth assessment. They’ll take note of your heating requirements, size of home and available space as well as soil geology before suggesting an ideal ground loop system to meet those needs. They might also suggest installing new heat exchangers and distribution networks.

 

After conducting an initial inspection, contractors will dig trenches around your property based on your chosen ground loop system type – this could take anywhere from one to two meters deep trenches depending on which ground loop type you choose – before installing polyethylene pipes to complete it in about 1-2 days.

 

As soon as your ground loop piping is in place, your contractor will install the heat pump inside your house to replace your existing boiler or HVAC system. They’ll connect it to ductwork and ground loop piping, as well as installing any hot water tanks you might have.

 

Your installer will connect the heat pump unit to ductwork, ground loop and any underfloor heating systems in your home, as well as conduct water testing to ensure that it is clean and free of contaminants. They will then purge ground arrays by passing an antifreeze solution through them; purging will prevent your heat pump from freezing over and destroying its equipment.

 

Once installation is complete, your technician will test and examine your new system, providing an explanation as well as handover, so you know exactly how to use it. They may even offer maintenance packages or aftercare services for continued peace of mind.

 

Maintenance

 

Ground source heat pumps offer an eco-friendly alternative to traditional heating systems, yet their installation can be complicated. Qualified contractors should only undertake such an endeavor, since a properly designed system is crucial in terms of performance and energy savings. Your contractor will assess your home’s current heat loss, hot water requirements, insulation levels, and insulation levels before suggesting an ideal solution based on site geography, geology and hydrology of where your heat pump will be situated.

 

They will dig trenches on your property and install piping that will be filled with an antifreeze and water mixture before being connected to a heat pump and ductwork, either replacing your current ducts or being installed for something new such as underfloor heating systems. Depending on the size of your property, this process may take three or four days with just a one-man team working.

 

Before hiring an installer, be sure to discuss the timeline for your project with them. Timing can have a dramatic impact on cost and complexity of installation – for instance it would be wiser not to install ground-source heat pumps during rainy seasons as this can cause flooding issues and other complications; landscaping could also wait until after completion has taken place.

 

At the time of installation, your contractor will inspect your yard for existing septic tanks and drinking water wells before excavating ground-source heat pump wells. They’ll also search for any utilities running beneath your property to make sure that they won’t interfere with your system, while working closely with local authorities to ensure compliance with local codes and regulations for ground-source heat pumps.

 

Once your contractor has installed your heat pump, they will connect it to your ductwork and ground loops before testing and making any necessary adjustments to the system. If using for domestic hot water use only, they will also connect it directly to any existing or newly purchased hot-water cylinders.

 

Warranty

 

Homeowners looking for ways to reduce their environmental footprint may benefit from installing a ground source heat pump installation service in their home. These systems can save up to 30-60% in heating costs and 20-50% on cooling costs, providing fast return on investment and fast savings potential. Moreover, heat pumps are more energy-efficient than conventional fossil fuel boilers; therefore lowering electricity demand and energy prices while helping eliminate new power plant developments altogether.

 

Ground-source heat pump systems use natural underground temperatures to provide heating for your property, whether that be space heating, water heating or air conditioning needs. They’re environmentally-friendly too – perfect for homes that already exist or new construction alike as well as commercial properties; installation procedures depend on which ground-source heat pump type is chosen, and any necessary excavation works required for setup.

 

Finding a reputable installer of ground-source heat pumps is crucial, so make sure that they are licensed and insured, MCS approved, REAL members as well as offering warranties which offer long term peace of mind.

 

Your contractor will conduct a heat load calculation to make sure the system is the appropriate size, tailoring it specifically to meet your energy savings goals and taking advantage of state and local incentives. In addition, they’ll inspect any preexisting ductwork to ensure it’s adequately insulated.

 

Once installed, a ground-source heat pump will be connected to both ductwork and ground loop. A contractor will test its efficiency by monitoring how heat moves between these elements as well as air temperatures within your home – provided your ground source heat pump was appropriately sized, you should experience minimal temperature fluctuations.

 

Notably, ground-source heat pumps require annual maintenance visits from contractors for proper functioning and inspection purposes. Along with purging any excess water from ground arrays and flushing the ground arrays annually to avoid scale or algae build-up. This should all take place prior to turning on the heat pump for its first turn-on of each year.

 

About Author